If you have this type of drip edge, apply a bead of clear silicone caulk to the back lip of the drip edge and push it back into place. I don’t particularly like sweeps that are secured with caulk only because they seem to work themselves loose quickly. These sweeps are likely to be held in place with silicone caulk. Some types of drip edges have a groove that the sweep slides into. If the sweep needs to be replaced, buy a new one at a home improvement or plumbing supply store and sandwich it in between the door and drip edge (you may have to trim it). To adjust the sweep, loosen the screws (don’t remove them), and pull the sweep down evenly so that it just touches the bottom track of the shower. If your drip edge is held in place with screws, this job is easy. It will probably be a little wavy, but that’s OK. The drip edge and sweep are usually held in place with a couple of screws, but I have seen them held in place with silicone caulk or even double-sided tape. The sweep can be adjusted or replaced to eliminate this gap. Often, the friction from opening and closing the door will cause the shower sweep to recede up into the drip edge, leaving a gap for water to splash through. The sweep typically rubs against the bottom track of the shower. The nice thing though is that it’s permanent. You know how when you open the door from the inside of the shower you sometimes have to push a little harder than normal? That extra effort pushed all those chemicals on the carpet, leaving a rainbow arc of discoloration. The chemicals worked their way down to the drip edge. Well, I got a little lax on squeegeeing the glass after a shower so she bought some chemicals to spray on the glass to leave a streak-free surface. Now, my wife is a cleaning fanatic who goes ballistic if there is even a drop of water on the glass, so she bought a squeegee. The sweep attaches to the inside bottom of the door and has a drip edge to direct water back into the shower, and a rubber sweep on the bottom of the door to keep water from splashing out. Like many people, I have a glass shower door with a sweep on the bottom of it. How can I prevent the water from leaking out?Ī: Most of the complaints I hear about leaking shower doors are that they leak from underneath the door (like yours). My neighbor came over and said it looks like my shower door is missing a part at the bottom of it. If your new sweep still doesn't seem to help prevent water from leaking, consider using caulk to reseal the base of the shower, or call a plumber for a professional opinion.Q: I have a problem with water creeping under my shower door when I shower. If the sweep is too long, you may need to adjust the size once again with scissors. If the new sweep sticks while you're trying to install it, or if it seems to be a bit too tight to fit into the shower, use petroleum jelly to help lubricate it. It should fit very snugly and create an air-tight seal so that water will not be able to leak out of the base of the shower. Step 4 - Install the New Sweepįit the new sweep into the base of the shower. At this point, the two sweeps should be exactly the same height and length, and you're ready to install the new sweep into the shower base. Use a pair of scissors to cut the new sweep so that it's the same length as the old one. The height of the two sweeps should be the same, but the new sweep will likely be longer than the existing one this is not a problem. If you had a difficult time determining the proper size for your replacement sweep, take the removed sweep in to a hardware store in order to match it with a new one. If the sweep is connected to the base of a shower door track, you may need to unscrew it from the track in order to remove it. If the sweep is glued down to the base of the shower, grab one of the ends of the sweep and firmly pull the sweep away from the door until the entire piece gradually comes loose. Open the shower door and prepare to remove the existing shower sweep. If you have trouble determining the sweep that you'll need, consult with a representative at the store. New door sweep (of the same size and design as the previous one)Ī new door sweep is available at a hardware or home improvement store.Gather the following items before you begin: Step 1 - Collect Your Materials and Toolsīefore you begin to install a new shower sweep, you'll need to collect all of the proper materials and tools for the job.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |